Skip to content
Semi Vietnam
Get a quote

Guides / Process

Anodizing in Vietnam: What Is Local, What Is Subcontracted and What to Ask

November 4, 2026

Set of black anodised aluminum heatsinks in five sizes, parts finished by anodizing
Photo: Lucasbosch, CC BY-SA 4.0, via Wikimedia Commons (resized)

We found no public count of anodizing lines in Vietnam, so the capacity cannot be sized from outside. What a buyer can check is narrower and more useful: whether the line that will coat your parts has a valid environmental permit, whether it runs to a named specification, and whether it records each lot. This guide covers those checks and the drawing call-outs that let any anodizer quote the job.

What we could and could not find

We looked for a directory or a statistic on anodizing and plating capacity in Vietnam and found none we could verify. A few market reports exist behind paywalls, and we did not rely on them. What is public is the regulation that every wet finishing line has to live under, plus the standards that define the coating itself.

So the useful question is not “is there an anodizer in Vietnam”. It is “who runs the line that will coat my part, and what can they show me”. The rest of this guide is built around that question. The finishing queue is the reason it matters for the schedule, as where the weeks go on a machined part explains.

The rules a line has to live under

Two public rules shape who can run an anodizing line and what it costs.

An environmental permit. The 2020 Law on Environmental Protection requires operations with waste sources to hold an environmental permit (Article 39, clause 2, as cited in the press). The risk of running without one is not theoretical. In March 2025 the Bac Giang Provincial People’s Committee fined two factories VND320 million each for operating without a required permit and suspended their waste-generating operations for 4.5 months. One was a precision mechanical processing plant and the other an electronic components factory. Neither is reported as an anodizer, but the penalty shows what a missing permit can do to a delivery date.

An effluent standard. QCVN 40:2025/BTNMT is the national technical regulation on industrial effluent, issued under Circular 06/2025/TT-BTNMT on 28 February 2025 and in force from 1 September 2025. New projects and projects that expand scale or capacity must meet it from that date. Existing facilities and projects approved earlier may keep applying the previous rules until 31 December 2031 and must comply from 1 January 2032.

Table 2 of the regulation sets limits for metals that finishing lines handle. Examples are hexavalent chromium at 0.1 mg/L in column A and 0.5 mg/L in columns B and C, and nickel at 0.1 mg/L in column A and 3.0 mg/L in columns B and C. Aluminum does not appear in Tables 1 or 2. Surface treatment has no category of its own in Appendix 2, so the controlled parameters for a line are set case by case in its environmental assessment or permit.

The practical reading, which is ours and not the regulation’s wording: the age and permit status of a line tell you something about its compliance path. Ask when the line was permitted and whether it has expanded since.

What goes on the drawing so any anodizer can quote it

An anodize note that says only “anodize black” gets five different quotes. These call-outs let the finisher price the same job.

Call-out What to write Why
Process specification MIL-A-8625 with Type and Class, or the specification your plant uses Types I, II and III are chromic, sulfuric and hard coat; Class 1 is undyed and Class 2 is dyed
Thickness A minimum and a maximum, in micrometres Each surface grows by about half the coating thickness, so tolerance on a fit depends on it
Sealing Required or not, and the method if you care Sealing is described as required for Types I and II and optional for Type III
Masked features List the threads, bores and contact faces, with the datum Masking costs labor; unlisted features get coated
Racking marks Where contact marks are acceptable Every part touches a rack somewhere
Alloy and colour The alloy and a colour reference Copper and silicon reduce corrosion resistance and make light colours hard to hold
Certificate Certificate of conformance, with the lot and thickness result You need a record per lot, not a promise

The dimension effect is worked through in hard anodize or electropolish, and the alloy response is in aluminum alloys for semiconductor parts. Both are worth reading before you set a tolerance on an anodized fit. The nickel alternative for tooling is in electroless nickel plating.

Thickness figures for the types vary between summaries. One reference gives about 1.8 to 25 micrometres for Type II and up to 150 micrometres for hard coats. A vendor summary of the specification gives narrower ranges. Take the thickness range from the current specification and your own drawing, not from a blog.

Need a quote for this part? Get a quote

Questions for the shop and its finisher

  1. Does the shop run the line itself, or does a partner? The quote should say. If it is a partner, ask who is responsible for the result and for the lot record.
  2. What is the environmental permit and when was it issued? A shop that sends parts out should be able to say its partner holds one.
  3. Which specification does the line run to? A named Type and Class, not “standard anodize”.
  4. How is thickness measured and recorded? On the part, on a witness coupon, or both. For a fit, ask for the numbers per lot.
  5. What is the minimum lot, and when does the bath run? Baths run in batches. A single part can wait for a full rack, which is why finishing stretches a four-week job.
  6. Which days does the finisher close? Add it to the Tet plan if the order crosses the break.
  7. What happens to a rejected lot? It may be stripped and recoated. Agree before the order whether that is allowed on a toleranced fit.

Each question has a short answer. A shop that can give all seven in an email has a process you can audit. One that answers with “no problem” has not answered.

Where this fits in the quote

The finishing line belongs in the quote breakdown as its own entry, with its own lead time. If it is folded into a single price with no days attached, ask for it to be separated. A change to the finish after the order restarts the queue, so settle the call-out before release. The drawing habits that avoid a requote are in drawing mistakes that stop a quote.

Alkaline cleaning agents can attack anodized coatings; see cleaning agents against fixture materials and our guide to semiconductor tooling materials.

If you have an anodized aluminum part and want it quoted by shops that name their finisher and their specification, send the RFQ with the call-outs above in the drawing notes. We come back within 24 business hours with a quote or a plain no. How shops are screened is on how an order runs.

See also: environmental records a customer reads in a Vietnam machine shop.

Sources

Frequently asked questions

Can aluminum parts be anodized in Vietnam?

Machine shops here quote anodized parts, but we found no public register of anodizers, so the capacity cannot be counted from outside. Many shops send aluminum to a finishing partner. The quote should say whether the line belongs to the shop or a partner, and under whose environmental permit it runs.

Does MIL-A-8625 require sealing on hard anodize?

Summaries of the specification say sealing is required for Types I and II and optional for Type III. That is a secondary description, so read the current revision of MIL-A-8625 before you write the drawing. If sealing matters to you, state it as a requirement either way.

What wastewater rule applies to an anodizing line in Vietnam?

QCVN 40:2025/BTNMT, issued under Circular 06/2025/TT-BTNMT, applies to new and expanded projects from 1 September 2025. Existing facilities may follow the earlier rules until 31 December 2031 and must comply from 1 January 2032. Surface treatment has no category of its own in the appendix, so the controlled parameters are set case by case in the permit.

What should I ask an anodizer to show before I send parts?

Ask for a copy of its environmental permit, the process specification it will run to, a record of the thickness measurement method and a sample certificate. A finisher that can show all four has a process you can audit. One that cannot is a risk to your schedule as well as to your quality.

Need a quote for this part?

Send the drawing. We quote the finished parts, place the work with a partner shop in Vietnam and reply within 24 business hours.

Get a quote

More on process

All guides and the sourcing glossary.