Home / Processes
CNC and Finishing Processes Available in Vietnam
What a shop here usually runs under its own roof, what it buys from a specialist and where the chain is still thin. Read it before you compare two lead times.
Process by process
A working picture of where each process usually sits, not a census. Individual shops vary, which is why we check the chain behind a shop and not only its machine list.
| Process | Where it usually sits | Used on semiconductor work for | Ask the shop |
|---|---|---|---|
| 3-axis milling | In house at most precision shops | Jig plates, brackets, EFEM hardware, covers | Largest plate they run in one setup |
| 4 and 5-axis milling | In house at some shops | End effectors, manifolds, parts with angled features | Simultaneous 5-axis or positional 3+2 |
| CNC turning and mill-turn | In house at most precision shops | Flanges, pins, bushings, fitting bodies | Bar capacity and live tooling |
| Surface grinding | In house at tooling and jig shops | Hardened plates, parallels, change kit parts | Flatness reached on your plate size, and how it is measured |
| Jig grinding | In house at some shops | Locating and dowel holes in hardened plates | Bore tolerance they hold on hardened steel |
| Wire EDM | In house at tooling and jig shops | Nest pockets, punch profiles, hardened slots | Wire size, number of skim passes, maximum thickness |
| Sinker EDM | In house at tooling and jig shops | Blind cavities and fine detail in hardened steel | Electrode material and who makes the electrodes |
| Heat treatment | Usually bought from a specialist | SKD11 and SKD61 tooling, 440C pins, 17-4 PH aging | Furnace type and a hardness report per batch |
| Type II and Type III anodize | Usually bought from a specialist | Aluminum jigs, EFEM parts, chamber parts | Specification, thickness check, seal method |
| Electroless nickel | Usually bought from a specialist | Steel and aluminum tooling, wear faces | Phosphorus range and thickness report |
| Passivation | Usually bought from a specialist | Stainless parts after machining | ASTM A967 method and the test used |
| Electropolish for high purity | Few suppliers in the country | Gas wetted 316L, UHV hardware | Ra after polishing and who measured it |
| TIG welding and stress relief | In house at some shops | Frames, bases, weldments | Welder qualification, stress relief before final machining |
| Laser marking | In house at most precision shops | Part number, lot and serial marking | Mark content, depth and position on the drawing |
| CMM inspection | In house at some shops | First article and dimensional reports | Machine, calibration date, report format |
| Cleanroom cleaning and packing | Few suppliers in the country | Equipment and chamber parts | Written procedure, bag type, class of the packing area |
How we hold a shop against its chain is written out in how an order runs.
Two routes, two different shops
Semiconductor parts made here tend to follow one of these two routes. They need different machines, different finishers and a different kind of shop.
Hardened change kit part
A nest, guide or punch for an assembly or test line.
- SKD11 or SUS440C block, rough milled with grinding stock left
- Vacuum hardened and tempered at a heat treater
- Surface ground to thickness and flatness
- Profile and pockets cut by wire EDM
- Locating holes finished by jig grinding
- Laser marked, inspected, oiled or bagged
Anodized aluminum equipment part
A bracket, plate or chamber part for a tool.
- A6061-T651 plate with a mill certificate
- Rough milled, rested, then finish milled
- Deburred and degreased before it leaves the shop
- Hard or clear anodize at a finisher, threads masked
- CMM report on the features you named
- Cleaned, double bagged and labelled outside the bag
More on each step: wire EDM jig plates, jig grinding locating holes, heat treating tool steel fixtures and hard anodize against electropolish.
Typical tolerance by process
Ranges usually held on this kind of work, not promises. The shop that quotes confirms what it holds on your geometry, material and size.
| Process | Typical size tolerance | Typical form | Typical Ra |
|---|---|---|---|
| CNC milling | ±0.01 to ±0.02 mm | About 0.02 mm over 300 mm with care | 0.8 to 1.6 um |
| CNC turning | ±0.005 to ±0.01 mm on diameters | Roundness near 0.005 mm | 0.4 to 1.6 um |
| Surface grinding | ±0.002 to ±0.005 mm | About 0.005 mm over 300 mm | 0.2 to 0.4 um |
| Jig grinding | ±0.002 mm on bores | Position near 0.003 mm | 0.2 to 0.4 um |
| Wire EDM | ±0.005 mm with skim passes | Profile accuracy set by the skims | 0.4 to 0.8 um after skims |
| Sinker EDM | ±0.01 mm | Depends on electrode wear | 0.8 to 3.2 um |
A tolerance the function does not need costs money on every piece. How form tolerances add up across a fixture: tolerance stack up in fixtures. Background on the spark erosion processes: electrical discharge machining.
Where the weeks go
Cutting time is rarely the long part. These four things are.
- Outside processesEvery heat treatment, anodize or plating step adds a transport leg and a queue at someone else's line.
- BatchingHeat treaters and anodize lines run in batches. A part that just misses a batch waits for the next one.
- Finisher distanceA finisher two provinces away adds days to every order. The regional capacity guide shows where the chains are.
- Imported stockGrades that are not stocked locally wait for material before anything is cut. See materials for what is usually local.
Questions about processes
The cost side is in lead time and finishing bottlenecks.
Can I get 5-axis machining in Vietnam?
Yes, at some shops. Ask whether the machine runs simultaneous 5-axis or positions the part and cuts on three axes, and ask for a similar part they have made. For end effectors and manifolds the positional method is often enough and cheaper.
Is electropolishing for high purity parts available locally?
There are few lines suited to gas wetted or UHV work, and the supporting cleaning chain is thinner than the machining base. If no qualified line fits your part we tell you so rather than send it to a shop that will learn on it.
Who manages the outside processes?
The shop you order from. It buys the heat treatment, anodize or plating and answers to you for the result. Ask it to name each finisher and where it is, because that answer explains most of the lead time.
Do shops here read ASTM drawings, or only JIS?
Both. JIS material names and habits are common, because many shops grew up working for Japanese and Korean plants. An ASTM or EN drawing is fine, and giving the material in both systems removes one round of questions.
Send the drawing, name the route
Say which finishes and inspections you need. We quote the finished parts, place the work with a partner shop whose chain fits and reply within 24 business hours. Parts by buyer type are on industries.